Thodian
Wendigo
- Joined
- Feb 12, 2026
- Posts
- 9,420
- Reputation
- 16,705
Made for @woodyy dont do sarms with no test base
What are SARMs?
SARMs are Selective Androgen Receptor Modulators.
It is synthetic chemicals to mimic the effects of testosterone and other compounds without the same side effects.
But do NOT use them without a testosterone base.
It still stops your bodies natural production.
In short it will get you jacked without DHT conversion.
If you are an iqlet and don't know how to prevent the norwood reaper.
What is YK-11?
Compound that inhibits myostatin.
What is myostatin? It is a protein in your body that stops muscles from getting too large.
Increases follistatin production.
What is follistatin production? Forces your muscle cells to intake more.
Partial agonist to androgen receptor binding.
Without further ado this is what you will need.
Raw Yk-11 powder.
Beaker
Lab hot plate with a magnetic stirrer
A Stirrer Bar
Sterile Vials
10ML Luer Lock Syringes
.22 Filter Syringes
18g Needles
Benzyl Benzoate
Benzyl Alcohol
MCT Oil
~This is my personal recipe so it will be for 80ML~
This will be a recipe dosed at 62.5mg per ML.
If you want a custom amount it is simple math.
1G of powder is = 1000mg.
Depending how much carrier, BA, and BB you use will be divided into that amount.
Example if you use a total of 20ML of liquids for 5g of powder.
It will be 250mg per ML final product.
~Brewing~
These will be the ratios you will use for each liquid.
18% Benzyl Benzoate
2% Benzyl Alcohol
80% Carrier Oil aka MCT oil or GSP oil
So you will first add your benzyl benzoate, benzyl alcohol, and carrier oil in the beaker on top of the hot plate.
BUT DO NOT HEAT IT UP YET. ONLY TURN ON THE MAGNETIC STIRRER.
Why? Because yk-11 doesn't always need to be heated to be dissolved.
I try to avoid heating it at all costs because it can cause crashing.
What is crashing? This is when crystals and flakes form due to rapid temperature fluctuation.
Once your bb, ba, and carrier oil has been mixing for about 5 minutes you will add your yk-11 powder.
When do I know if I need to heat it up?
After 10 minutes of adding your raw powder in the beaker and it not showing signs of dissolving.
If you HAVE to heat it up be very gentle heat it at a low degree.
Once the raw powder is fully dissolved let it sit for 10 minutes.
~Filtering~
You will get your 10ml Leuer lock syringes.
Add the 18g needle then draw your brewed oil.
Then take off the 18g needle.
And add the .22 Syringe Filter and 18g needle again.
It should look like this.
Then you will grab your sterile vials and start to add the oil inside.
Should look like this.
Yes you will need to add another needle to act as an air pressure gauge.
If not it will have the possibility of pushing the oil up due to a pressure bubble.
There you go you have brewed injectable yk-11.
I will link all the products needed below. Besides a powder source.
Product Links
Beaker
Lab Hot Plate
Stirrer Bar
.22 Syringe Filter
10ML Luer Lock Syringe
Sterile Vials
18g Needles
MCT Oil
Benzyl Benzoate
Benzyl Alcohol
What are SARMs?
SARMs are Selective Androgen Receptor Modulators.
It is synthetic chemicals to mimic the effects of testosterone and other compounds without the same side effects.
But do NOT use them without a testosterone base.
It still stops your bodies natural production.
In short it will get you jacked without DHT conversion.
If you are an iqlet and don't know how to prevent the norwood reaper.
What is YK-11?
Compound that inhibits myostatin.
What is myostatin? It is a protein in your body that stops muscles from getting too large.
Increases follistatin production.
What is follistatin production? Forces your muscle cells to intake more.
Partial agonist to androgen receptor binding.
Without further ado this is what you will need.
Raw Yk-11 powder.
Beaker
Lab hot plate with a magnetic stirrer
A Stirrer Bar
Sterile Vials
10ML Luer Lock Syringes
.22 Filter Syringes
18g Needles
Benzyl Benzoate
Benzyl Alcohol
MCT Oil
~This is my personal recipe so it will be for 80ML~
This will be a recipe dosed at 62.5mg per ML.
If you want a custom amount it is simple math.
1G of powder is = 1000mg.
Depending how much carrier, BA, and BB you use will be divided into that amount.
Example if you use a total of 20ML of liquids for 5g of powder.
It will be 250mg per ML final product.
~Brewing~
These will be the ratios you will use for each liquid.
18% Benzyl Benzoate
2% Benzyl Alcohol
80% Carrier Oil aka MCT oil or GSP oil
So you will first add your benzyl benzoate, benzyl alcohol, and carrier oil in the beaker on top of the hot plate.
BUT DO NOT HEAT IT UP YET. ONLY TURN ON THE MAGNETIC STIRRER.
Why? Because yk-11 doesn't always need to be heated to be dissolved.
I try to avoid heating it at all costs because it can cause crashing.
What is crashing? This is when crystals and flakes form due to rapid temperature fluctuation.
Once your bb, ba, and carrier oil has been mixing for about 5 minutes you will add your yk-11 powder.
When do I know if I need to heat it up?
After 10 minutes of adding your raw powder in the beaker and it not showing signs of dissolving.
If you HAVE to heat it up be very gentle heat it at a low degree.
Once the raw powder is fully dissolved let it sit for 10 minutes.
~Filtering~
You will get your 10ml Leuer lock syringes.
Add the 18g needle then draw your brewed oil.
Then take off the 18g needle.
And add the .22 Syringe Filter and 18g needle again.
It should look like this.
Then you will grab your sterile vials and start to add the oil inside.
Should look like this.
Yes you will need to add another needle to act as an air pressure gauge.
If not it will have the possibility of pushing the oil up due to a pressure bubble.
There you go you have brewed injectable yk-11.
I will link all the products needed below. Besides a powder source.
Product Links
Beaker
Lab Hot Plate
Stirrer Bar
.22 Syringe Filter
10ML Luer Lock Syringe
Sterile Vials
18g Needles
MCT Oil
Benzyl Benzoate
Benzyl Alcohol
