Testosterone injections

[Tristanb_]

I honestly can't be fucked to by multiple needles. Would it be fine to just use the same one I draw with to inject? I don't care about pain.

 

[Hater_of_foids]

I don't care about pain.

sigma

 

[Tristanb_]

sigma

No like actualy is it chill.

 

[James holder]

you can and most people do

 

[Ant!]

I honestly can't be fucked to by multiple needles. Would it be fine to just use the same one I draw with to inject? I don't care about pain.

Its not about the pain but infections and such,if you disinfect it you should be fine as long as its not damaged in any way. Also just dont use the same one for too long

 

[vexd]

I pin my oils sub c with insulin syringes

 

[iLoveCavan]

I honestly can't be fucked to by multiple needles. Would it be fine to just use the same one I draw with to inject? I don't care about pain.

Depends, you need to to draw from multiple vials then fuck no, but if your only drawing from one and then pinning its fine

 

[foidfondler]

no don't follow the correct protocol:

• Use A Draw Needle: Without one, you will dull your pin needle to the point that it'll be very painful and potentially give a pip.
  Note: If your syringes come with the needles already attached, order the drawing needle to come on them. Otherwise, you'll have to switch needles, more than necessary.
• Clean The Vial: Wipe top of the vial with an alcohol pad/swab and let dry.
• Draw Air: Uncap the needle and fill the syringe with as much air as you plan to withdraw in liquid. (i.e. If you plan to inject 1.5 mL/cc of liquid, you will draw 1.5 mL/cc of air.)
• Inject The Air Into The Vial: Inject the air into the vial to create positive pressure inside the vial. This will assist and make drawing easier.
• Draw The Liquid: Draw your required mL/cc of liquid while ensuring to keep the needle point in the liquid.
• Change To Your Injection Needle: Cap the drawing needle and remove the drawing needle from the syringe. Attach your injection needle to the syringe.
• Clean The Area: Clean the area you want to inject with a new alcohol swab in an outward going circular motion and let dry. Uncap your injection needle.
• Inhale, Then Exhale Slowly: Inhale deeply, and while exhaling insert the needle. This serves to decrease the chances of muscle spasms.
• Insert The Needle: Insert needle in a fast and precise motion, push needle in until 2 mm or so is exposed.
• Aspiration (OPTIONAL): Gently draw (pull) back on the plunger by a few millimeters. If no blood enters the barrel, proceed. If blood pours into the barrel, see [Aspiration]( )
• Push The Plunger: Push the plunger on the syringe, injecting the liquid into the muscle slowly and smoothly.
  Note: As a general rule of thumb, always inject slowly; take 30 seconds per mL.
• Pull The Needle Out: Pull the needle out and cap it, then swab the area with a alcohol pad/swab.
• Legally Dispose: Dispose of your medical sharps (needles) properly.

 

[foidfondler]

I pin my oils sub c with insulin syringes

what abt bumps? I tried this before with test and primo and it was fucked

 

[vexd]

what abt bumps? I tried this before with test and primo and it was fucked

I do it with tren lol, it basically just burns my fat or sum it feels like genuinely acid no bumps tho I just pin deep enough

 

[foidfondler]

I do it with tren lol, it basically just burns my fat or sum it feels like genuinely acid no bumps tho I just pin deep enough

only tren will get your T high enough to do that shit mirin tho

 

[Tristanb_]

no don't follow the correct protocol:

• Use A Draw Needle: Without one, you will dull your pin needle to the point that it'll be very painful and potentially give a pip.
  Note: If your syringes come with the needles already attached, order the drawing needle to come on them. Otherwise, you'll have to switch needles, more than necessary.
• Clean The Vial: Wipe top of the vial with an alcohol pad/swab and let dry.
• Draw Air: Uncap the needle and fill the syringe with as much air as you plan to withdraw in liquid. (i.e. If you plan to inject 1.5 mL/cc of liquid, you will draw 1.5 mL/cc of air.)
• Inject The Air Into The Vial: Inject the air into the vial to create positive pressure inside the vial. This will assist and make drawing easier.
• Draw The Liquid: Draw your required mL/cc of liquid while ensuring to keep the needle point in the liquid.
• Change To Your Injection Needle: Cap the drawing needle and remove the drawing needle from the syringe. Attach your injection needle to the syringe.
• Clean The Area: Clean the area you want to inject with a new alcohol swab in an outward going circular motion and let dry. Uncap your injection needle.
• Inhale, Then Exhale Slowly: Inhale deeply, and while exhaling insert the needle. This serves to decrease the chances of muscle spasms.
• Insert The Needle: Insert needle in a fast and precise motion, push needle in until 2 mm or so is exposed.
• Aspiration (OPTIONAL): Gently draw (pull) back on the plunger by a few millimeters. If no blood enters the barrel, proceed. If blood pours into the barrel, see [Aspiration]( )
• Push The Plunger: Push the plunger on the syringe, injecting the liquid into the muscle slowly and smoothly.
  Note: As a general rule of thumb, always inject slowly; take 30 seconds per mL.
• Pull The Needle Out: Pull the needle out and cap it, then swab the area with a alcohol pad/swab.
• Legally Dispose: Dispose of your medical sharps (needles) properly.

holy cop

 

[foidfondler]

holy cop

u might just be a retard buddy if you think not wanting to get a needle infection or unnecessary pin pain = being a cop dumb nigga you've probably never touched or seen gear in your life

 

[Tristanb_]

u might just be a retard buddy if you think not wanting to get a needle infection or unnecessary pin pain = being a cop dumb nigga you've probably never touched or seen gear in your life

my bad bud but take a look at all the other replies or ask AI and you know they have hella saftey filters yet they still say it's fine

 

[foidfondler]

my bad bud but take a look at all the other replies or ask AI and you know they have hella saftey filters yet they still say it's fine

sure its fine but for me personally I use 2 because its easier to draw with a 21 gauge and easier to pin with a 25 gauge I just don't really see the point in just using one if its objectively less practical and needles are dirt cheap just to save like 30 seconds of your time

 

[Tristanb_]

sure its fine but for me personally I use 2 because its easier to draw with a 21 gauge and easier to pin with a 25 gauge I just don't really see the point in just using one if its objectively less practical and needles are dirt cheap just to save like 30 seconds of your time

I respect it